Home
Replacement
Operator WorkSpace Replacement
Replacing the GOC hard drive
Removal and installation instructions for replacing the solid state drive (SSD) on the host computer.
Installing the GOC hard drive
Install the solid state drive (SSD) in the host computer.

Replacement
- Operator WorkSpace Replacement
  - Dell T5810 Computer Replacement
  - Dell T5810 Lower Level FRU Replacement
  - HUB Replacement
  - PCI AA Replacement
  - GOC Dust Filter Clean/Replacement Procedure
  - Temperature & Humidity Sensor Replacement
  - GOC PDU Replacement
  - Replacing/Installing the SCIM, Keyboard and Mouse
  - Electrical Safety
    You must follow all recommended safety procedures when servicing and working near energy sources.
  - Shutting down the host computer
    Shutting down the host computer shuts down the system safely and turns off the power to the host computer.
  - Starting up the host computer
    How to start the host computer.
  - Doing a check scan
    A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
  - LCD Monitor Replace with HP HC240
  - Replacing the host computer - Dell T5820
    Removal and installation instructions to replace the host computer when upgrading the system.
  - Replacing the GOC hard drive
    Removal and installation instructions for replacing the solid state drive (SSD) on the host computer.
    - Electrical Safety
      You must follow all recommended safety procedures when servicing and working near energy sources.
    - Preparing the workstation for a computer replacement
      Prepare the workstation so all data is saved prior to shutting down and replacing the host computer in the GOC.
    - Shutting down the host computer
      Shutting down the host computer shuts down the system safely and turns off the power to the host computer.
    - Lockout / Tagout for the GOC
    - Removing the host computer
      Remove the host computer from the GOC when upgrading the system.
    - Removing the GOC hard drive
      Remove the solid state drive (SSD) from the host computer.
    - Installing the GOC hard drive
      Install the solid state drive (SSD) in the host computer.
    - Installing the host computer
      Install the host computer in the GOC after it has been serviced or replaced.
    - Starting up the host computer
      How to start the host computer.
    - Finalizing computer or drive replacement
      Follow this procedure to finalize a computer or hard drive replacement.
  - Replacing the DVD drive on the host computer
    Removal and installation instructions for replacing the DVD drive on the host computer.
  - Replacing the CMOS battery - Dell T5820
    Removal and installation instructions for replacing the CMOS battery in the host computer.
  - Clean Dust Filter / Dust Filter Replacement
  - Replacing the Global Operator Cabinet Audio Assembly (GOCAA)
    Removal and installation instructions for replacing the Global Operator Cabinet Audio Assembly (GOCAA).
  - Replacing the Global Operator Cabinet (GOC) Power Distribution Unit (PDU)
    Removal and installation instructions for replacing the Power Distribution Unit (PDU) in the Global Operator Cabinet (GOC).
  - Replacing the CMOS battery - Dell T5820
    Removal and installation instructions for replacing the CMOS battery in the host computer.
- System Cabinet Replacement
- Magnet Enclosure and Outer Electronics
- Rear Pedestal Replacement
- LPCA Replacement
- Coil Replacements
- Lite Patient Transport Replacement
- Low Height Fixed Table
- Coil Blower and Chiller Assemblies

SIGNA MR355 / SIGNA MR360
Service Manual
5856356-3EN Revision 5.0
Basic Service Documentation. Copyright General Electric Company.
Object ID: 00000018WIA3017B220GYZ
Topic ID: id_2007260 Version: 2.2
Date: Apr 23, 2020 8:43:03 PM

Installing the GOC hard drive

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	-	15 minutes	-


Tools and test equipment
Item	Quantity	Part number	Manufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set (can be used on magnets with magnetic fields > 1.5T)	1 Kit	5113258	-
ESD Mat	1	-	-
ESD Strap	1	-	-


Replacement parts
Item	Quantity	Part number	Manufacturer
512GB SATA III SFF SSD 3D-TLS or V NAND Memory	2	8780011-102	-


Required conditions
Use an antistatic wrist strap and mat while performing this procedure to prevent electrostatic discharge (ESD).
Access to both the front and rear of the operator console is required. Move the console away from walls and remove obstacles in the room.

About this task

The Dell T5820 has two SSDs, and they have the same installation procedure.

Procedure

Insert the HDD into the 3.5" bracket with the connector end of the hard drive towards the back of the HDD bracket.
Slide the HDD bracket back into the hard drive bay.
Install the HDD bracket.
1. Slide the bracket into the drive bay until it clicks into place.
  
  CAUTION: Ensure that the latch is open before installing the bracket.
2. Lock the latch.
Install the HDD bezel.
1. Hold the bezel and ensure that the hooks on the bezel snap into the notches on the system.
2. Press the blue lock button on the left edge of the ODD bay to secure the bezel to the system.