Home
Replacements
Patient Table
Replacing the primary latch assembly
Removes the primary latch assembly from the dockable table and installs a replacement primary latch assembly.

Replacements
- Operator Workspace
- ISC (Integrated System Cabinet)
- ICC (Integrated Cooling Cabinet)
- Magnet Enclosure and Outer Electronics
- Coil Replacement
- Patient Table
  - Removing and installing the dockable table covers
    Provides removal and installation instructions for all dockable patient table covers.
  - Replacing a dockable table armboard
    Removes the left- or right-hand armboard from the dockable table and installs a replacement armboard.
  - Replacing the patient table braking system components
    Replaces braking system components for the dockable patient table.
  - Replacing a dockable table cable assembly
    Removes the P1/PE or P2/P4 cable assembly from the dockable patient table and installs a replacement cable assembly.
  - Replacing a table caster
    Removes one of the caster assemblies from the table base and installs a replacement caster.
  - Replacing the cradle flipper assembly
    Replaces the cradle flipper assembly in a dockable patient table.
  - Replacing the dockable table cradle
    Replaces the bottom half of the dockable table cradle.
  - Replacing a dockable table cradle side wheel
    Removes a side wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing a dockable table cradle vertical wheel
    Removes a vertically-oriented wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing the table dock cables
    Replaces the dock cables for the dockable patient table.
  - Replacing table dock components
    Procedures for replacing field replaceable units contained within the table dock.
  - Replacing the dockable table dummy load
    Removes the dummy load from the dockable table and installs a replacement dummy load.
  - Replacing the egress switch and springs
    Removal and installation instructions for replacing the egress switch and springs.
  - Replacing table electrical docking mechanism components
    Removes table components related to electrical docking and installs replacement components.
  - Replacing the dockable table ElectroMagnetic (EM) clutch and belt
    Removes the ElectroMagnetic (EM) clutch and belt from the dockable table motor and EM clutch assembly, and installs a replacement clutch and belt.
  - Replacing the handle hinge
    Removes the handle hinge from the dockable table and installs a replacement hinge.
  - Replacing the hydraulic cylinder
    Removes the hydraulic cylinder from a dockable patient table and installs a replacement hydraulic cylinder.
  - Replacing the hydraulic filter
    Removal and installation instructions for replacing the hydraulic filter in the dockable patient table.
  - Replacing the hydraulic rotary pump
    Replaces the hydraulic rotary pump of the dockable patient table.
  - Checking and filling hydraulic fluid
    Checks and adjusts the hydraulic fluid level for the dockable patient table.
  - Replacing the dockable table motor
    Removes the longitudinal movement motor from the dockable table and installs a replacement motor.
  - Replacing the dockable table motor coupler
    Removes the rigibelt drive to motor coupler from the dockable table and installs a replacement coupler.
  - Replacing the dockable table Physiological Acquisition Controller (PAC)
    Replaces the Physiological Acquisition Controller (PAC) on the dockable table.
  - Replacing the dockable table Posterior Array (PA) coil
    Removes the Posterior Array (PA) coil from the dockable table cradle and installs a replacement coil.
  - Replacing the primary latch assembly
    Removes the primary latch assembly from the dockable table and installs a replacement primary latch assembly.
    - Removing the dockable table bellows cover
      Removes the bellows cover from the dockable table.
    - Removing the right-hand table side cover
      Removes the right-hand cover from the dockable table.
    - Removing the left-hand table side cover
      Removes the left-hand cover from the dockable table.
    - Removing the tabletop front bumper
      Removes the front bumper from the dockable tabletop.
    - Removing the dockable table front lower bumper
      Dockable table lower front bumper removal.
    - Removing the dockable table handle-end cradle cover
      Removes the cover from the handle-end of the dockable table cradle.
    - Removing the dockable table cradle hardtop cover
      Removes the hardtop cover from the dockable table cradle.
    - Removing the right-hand base side cover
      Removes the right-hand cover from the dockable table base.
    - Removing the left-hand base side cover
      Removes the left-hand cover from the dockable table base.
    - Removing the oil catch pan
      Removes the oil catch pan from the dockable patient table.
    - Removing the primary latch assembly
      Disconnect and remove the primary latch assembly from the dockable table.
    - Installing the primary latch assembly
      Move the primary latch assembly into place on the dockable table and connect the adjustment cable.
    - Adjusting the primary latch
      Adjusting the primary latch as part of the replacement procedure.
    - Lowering the dockable table cradle
      Make primary latch adjustments and lower the cradle.
    - Adjusting the primary latch bar height
      Adjusts the height of the primary latch bar to properly hold and release the cradle in the home position.
    - Checking the dockable table interlocks
      Checks the measurements and operation of the table interlocks.
    - Installing the dockable table cradle hardtop cover
      Installs the hardtop cover onto the dockable table cradle.
    - Installing the dockable table handle-end cradle cover
      Installs the cover on the handle-end of the dockable table cradle.
    - Installing the oil catch pan
      Installs the oil catch pan onto the dockable patient table.
    - Installing the left-hand base side cover
      Installs the left-hand cover onto the dockable table base.
    - Installing the right-hand base side cover
      Installs the right-hand cover onto the dockable table base.
    - Installing the dockable table front lower bumper
      Dockable table front lower bumper installation.
    - Installing the tabletop front bumper
      Installs the front bumper onto the dockable tabletop.
    - Installing the left-hand table side cover
      Installs the left-hand cover onto the dockable table.
    - Installing the right-hand table side cover
      Installs the right-hand cover onto the dockable table.
    - Installing the dockable table bellows cover
      Installs the bellows cover onto the dockable table.
  - Replacing the reciprocating pump assembly
    Removes the reciprocating pump assembly from the dockable patient table and installs a replacement reciprocating pump assembly.
  - Replacing the respiratory connector or patient alert connector
    Provides instructions for replacing the respiratory connector or patient alert connector.
  - Replacing the dockable table rigibelt drive (actuator)
    Removes the rigibelt drive from the dockable table and installs a replacement drive.
  - Replacing the secondary latch actuating cable
  - Replacing the strain relief
    Removes the strain relief from the patient table handle-end cover and installs a replacement strain relief.
  - Replacing the dockable table string encoder
    Removes the string encoder from the dockable table and installs a replacement encoder assembly.
  - Replacing a dockable table touch-and-go assembly or side bumper
    Provides instructions for replacing a touch-and-go assembly or a side bumper on the dockable table.
  - Replacing table undock mechanism components
    Removes the undock link and lever from the table base and installs replacement components.
- MDP
- Pen Panel

SIGNA™ Hero 3.0T Service Methods
5852800-8EN Revision 1.0
Object ID: 00000018WIA30337E40GYZ
Topic ID: id_2020279 Version: 2.1
Date: Dec 13, 2019 10:41:40 AM

Replacing the primary latch assembly

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	-	2 hours and 20 minutes	5 minutes


Tools and test equipment
Item	Quantity	Part number	Manufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set	1	5113258	-
Stainless Steel Ruler	1	46-198452P2


Consumables
Item	Quantity	Part number	Manufacturer
Loctite #243	As required	5415261-3	-


Replacement parts
Item	Quantity	Part number	Manufacturer
Primary Latch Assembly	1	5796734	-


Required conditions
Table is undocked and away from the magnet.


Safety
Before working in any GE Healthcare MR suite or performing any GE Healthcare service procedure, you must: Have read and understood all hazard conditions and safety requirements in the latest revision of the GE Healthcare MR Service Safety Manual (5452735). Have successfully completed all relevant GE Healthcare Environmental Health and Safety (EHS) courses (or for non-GE employees, equivalent workplace training courses). Comply with all site-specific training and workplace safety requirements. If you have any safety concerns at any time, do not begin work or immediately stop work and move to a safe location. Immediately contact your supervisor or site safety officer for instructions on how to proceed.

CAUTION

Potential pinch hazard

Fingers placed in the path of moving components when checking the adjustment or operating the mechanism can be pinched.

Keep fingers clear of the moving components when checking the adjustment or operating the mechanism

Procedure

Undock the table and move it away from the magnet. If possible, move it out of the scan room.