Home
Replacements
Patient Table
Replacing the dockable table motor coupler
Removes the rigibelt drive to motor coupler from the dockable table and installs a replacement coupler.
Removing the right-hand table side cover
Removes the right-hand cover from the dockable table.

Replacements
- Operator Workspace
- ISC (Integrated System Cabinet)
- ICC (Integrated Cooling Cabinet)
- Magnet Enclosure and Outer Electronics
- Coil Replacement
- Patient Table
  - Removing and installing the dockable table covers
    Provides removal and installation instructions for all dockable patient table covers.
  - Replacing a dockable table armboard
    Removes the left- or right-hand armboard from the dockable table and installs a replacement armboard.
  - Replacing the patient table braking system components
    Replaces braking system components for the dockable patient table.
  - Replacing a dockable table cable assembly
    Removes the P1/PE or P2/P4 cable assembly from the dockable patient table and installs a replacement cable assembly.
  - Replacing a table caster
    Removes one of the caster assemblies from the table base and installs a replacement caster.
  - Replacing the cradle flipper assembly
    Replaces the cradle flipper assembly in a dockable patient table.
  - Replacing the dockable table cradle
    Replaces the bottom half of the dockable table cradle.
  - Replacing a dockable table cradle side wheel
    Removes a side wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing a dockable table cradle vertical wheel
    Removes a vertically-oriented wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing the table dock cables
    Replaces the dock cables for the dockable patient table.
  - Replacing table dock components
    Procedures for replacing field replaceable units contained within the table dock.
  - Replacing the dockable table dummy load
    Removes the dummy load from the dockable table and installs a replacement dummy load.
  - Replacing the egress switch and springs
    Removal and installation instructions for replacing the egress switch and springs.
  - Replacing table electrical docking mechanism components
    Removes table components related to electrical docking and installs replacement components.
  - Replacing the dockable table ElectroMagnetic (EM) clutch and belt
    Removes the ElectroMagnetic (EM) clutch and belt from the dockable table motor and EM clutch assembly, and installs a replacement clutch and belt.
  - Replacing the handle hinge
    Removes the handle hinge from the dockable table and installs a replacement hinge.
  - Replacing the hydraulic cylinder
    Removes the hydraulic cylinder from a dockable patient table and installs a replacement hydraulic cylinder.
  - Replacing the hydraulic filter
    Removal and installation instructions for replacing the hydraulic filter in the dockable patient table.
  - Replacing the hydraulic rotary pump
    Replaces the hydraulic rotary pump of the dockable patient table.
  - Checking and filling hydraulic fluid
    Checks and adjusts the hydraulic fluid level for the dockable patient table.
  - Replacing the dockable table motor
    Removes the longitudinal movement motor from the dockable table and installs a replacement motor.
  - Replacing the dockable table motor coupler
    Removes the rigibelt drive to motor coupler from the dockable table and installs a replacement coupler.
    - Lowering the dockable table bellows
      Detaches the dockable table bellows cover from the table side covers and lowers the bellows.
    - Removing the right-hand table side cover
      Removes the right-hand cover from the dockable table.
    - Removing the left-hand table side cover
      Removes the left-hand cover from the dockable table.
    - Removing the dockable table motor and clutch assembly
      Removes the motor and ElectroMagnetic (EM) clutch assembly from the dockable table tabletop.
    - Removing the dockable table motor coupler
      Removes the coupler from the rigibelt drive shaft.
    - Installing the dockable table motor coupler
      Installs the coupler onto the rigibelt drive shaft.
    - Installing the dockable table motor and clutch assembly
      Installs the motor and ElectroMagnetic (EM) clutch assembly onto the dockable table tabletop.
    - Installing the left-hand table side cover
      Installs the left-hand cover onto the dockable table.
    - Installing the right-hand table side cover
      Installs the right-hand cover onto the dockable table.
    - Raising the lowered dockable table bellows
      Raises a previously lowered dockable table bellows cover and attaches the bellows to the table side covers.
    - Doing the cradle motion test
      Makes sure the motion of the patient cradle into and out of the magnet bore is operating correctly.
    - Doing a check scan
      A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
  - Replacing the dockable table Physiological Acquisition Controller (PAC)
    Replaces the Physiological Acquisition Controller (PAC) on the dockable table.
  - Replacing the dockable table Posterior Array (PA) coil
    Removes the Posterior Array (PA) coil from the dockable table cradle and installs a replacement coil.
  - Replacing the primary latch assembly
    Removes the primary latch assembly from the dockable table and installs a replacement primary latch assembly.
  - Replacing the reciprocating pump assembly
    Removes the reciprocating pump assembly from the dockable patient table and installs a replacement reciprocating pump assembly.
  - Replacing the respiratory connector or patient alert connector
    Provides instructions for replacing the respiratory connector or patient alert connector.
  - Replacing the dockable table rigibelt drive (actuator)
    Removes the rigibelt drive from the dockable table and installs a replacement drive.
  - Replacing the secondary latch actuating cable
  - Replacing the strain relief
    Removes the strain relief from the patient table handle-end cover and installs a replacement strain relief.
  - Replacing the dockable table string encoder
    Removes the string encoder from the dockable table and installs a replacement encoder assembly.
  - Replacing a dockable table touch-and-go assembly or side bumper
    Provides instructions for replacing a touch-and-go assembly or a side bumper on the dockable table.
  - Replacing table undock mechanism components
    Removes the undock link and lever from the table base and installs replacement components.
- MDP
- Pen Panel

SIGNA™ Hero 3.0T Service Methods
5852800-8EN Revision 1.0
Object ID: 00000018WIA30DD5C40GYZ
Topic ID: id_2019286 Version: 2.6
Date: Jul 7, 2021 3:51:57 PM

Removing the right-hand table side cover

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	-	5 minutes	-


Tools and test equipment
Item	Quantity	Part number	Manufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set	1	5113258	-

Procedure

Remove the three screws securing the side cover to the table.

Figure 1. Right-hand side cover side screws
Remove the eight screws securing the side cover to the table.

Figure 2. Side cover bore-end bottom screws

Figure 3. Side cover handle-end bottom screws
Remove the right-hand table side cover from the table.

Note: The acrylic tube is supported by the left- and right-hand table side covers. Make sure the tube is still supported and does not drop when the cover is removed.

Figure 4. Right-hand side table cover