Home
Replacements
Patient Table
Replacing a dockable table touch-and-go assembly or side bumper
Provides instructions for replacing a touch-and-go assembly or a side bumper on the dockable table.
Replacing the dockable table left-hand bore-end touch-and-go assembly or side bumper
Removes the bore-end bumper on the left-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
Installing the tabletop front bumper
Installs the front bumper onto the dockable tabletop.

Replacements
- Operator Workspace
- ISC (Integrated System Cabinet)
- ICC (Integrated Cooling Cabinet)
- Magnet Enclosure and Outer Electronics
- Coil Replacement
- Patient Table
  - Removing and installing the dockable table covers
    Provides removal and installation instructions for all dockable patient table covers.
  - Replacing a dockable table armboard
    Removes the left- or right-hand armboard from the dockable table and installs a replacement armboard.
  - Replacing the patient table braking system components
    Replaces braking system components for the dockable patient table.
  - Replacing a dockable table cable assembly
    Removes the P1/PE or P2/P4 cable assembly from the dockable patient table and installs a replacement cable assembly.
  - Replacing a table caster
    Removes one of the caster assemblies from the table base and installs a replacement caster.
  - Replacing the cradle flipper assembly
    Replaces the cradle flipper assembly in a dockable patient table.
  - Replacing the dockable table cradle
    Replaces the bottom half of the dockable table cradle.
  - Replacing a dockable table cradle side wheel
    Removes a side wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing a dockable table cradle vertical wheel
    Removes a vertically-oriented wheel from the dockable table patient cradle and installs a replacement wheel.
  - Replacing the table dock cables
    Replaces the dock cables for the dockable patient table.
  - Replacing table dock components
    Procedures for replacing field replaceable units contained within the table dock.
  - Replacing the dockable table dummy load
    Removes the dummy load from the dockable table and installs a replacement dummy load.
  - Replacing the egress switch and springs
    Removal and installation instructions for replacing the egress switch and springs.
  - Replacing table electrical docking mechanism components
    Removes table components related to electrical docking and installs replacement components.
  - Replacing the dockable table ElectroMagnetic (EM) clutch and belt
    Removes the ElectroMagnetic (EM) clutch and belt from the dockable table motor and EM clutch assembly, and installs a replacement clutch and belt.
  - Replacing the handle hinge
    Removes the handle hinge from the dockable table and installs a replacement hinge.
  - Replacing the hydraulic cylinder
    Removes the hydraulic cylinder from a dockable patient table and installs a replacement hydraulic cylinder.
  - Replacing the hydraulic filter
    Removal and installation instructions for replacing the hydraulic filter in the dockable patient table.
  - Replacing the hydraulic rotary pump
    Replaces the hydraulic rotary pump of the dockable patient table.
  - Checking and filling hydraulic fluid
    Checks and adjusts the hydraulic fluid level for the dockable patient table.
  - Replacing the dockable table motor
    Removes the longitudinal movement motor from the dockable table and installs a replacement motor.
  - Replacing the dockable table motor coupler
    Removes the rigibelt drive to motor coupler from the dockable table and installs a replacement coupler.
  - Replacing the dockable table Physiological Acquisition Controller (PAC)
    Replaces the Physiological Acquisition Controller (PAC) on the dockable table.
  - Replacing the dockable table Posterior Array (PA) coil
    Removes the Posterior Array (PA) coil from the dockable table cradle and installs a replacement coil.
  - Replacing the primary latch assembly
    Removes the primary latch assembly from the dockable table and installs a replacement primary latch assembly.
  - Replacing the reciprocating pump assembly
    Removes the reciprocating pump assembly from the dockable patient table and installs a replacement reciprocating pump assembly.
  - Replacing the respiratory connector or patient alert connector
    Provides instructions for replacing the respiratory connector or patient alert connector.
  - Replacing the dockable table rigibelt drive (actuator)
    Removes the rigibelt drive from the dockable table and installs a replacement drive.
  - Replacing the secondary latch actuating cable
  - Replacing the strain relief
    Removes the strain relief from the patient table handle-end cover and installs a replacement strain relief.
  - Replacing the dockable table string encoder
    Removes the string encoder from the dockable table and installs a replacement encoder assembly.
  - Replacing a dockable table touch-and-go assembly or side bumper
    Provides instructions for replacing a touch-and-go assembly or a side bumper on the dockable table.
    - Replacing the dockable table left-hand bore-end touch-and-go assembly or side bumper
      Removes the bore-end bumper on the left-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
      - Lowering the dockable table bellows
        Detaches the dockable table bellows cover from the table side covers and lowers the bellows.
      - Removing the right-hand table side cover
        Removes the right-hand cover from the dockable table.
      - Removing the left-hand table side cover
        Removes the left-hand cover from the dockable table.
      - Removing the tabletop front bumper
        Removes the front bumper from the dockable tabletop.
      - Removing the dockable table left-hand bore-end side bumper
        Removes the bore-end bumper from the left-hand side of the dockable table.
      - Removing and installing the dockable table touch-and-go assembly
        Removes and installs the touch-and-go assembly from a dockable table side bumper for bumper or assembly replacement.
      - Installing the dockable table left-hand bore-end side bumper
        Installs the bore-end bumper onto the left-hand side of the dockable table.
      - Installing the tabletop front bumper
        Installs the front bumper onto the dockable tabletop.
      - Installing the left-hand table side cover
        Installs the left-hand cover onto the dockable table.
      - Installing the right-hand table side cover
        Installs the right-hand cover onto the dockable table.
      - Raising the lowered dockable table bellows
        Raises a previously lowered dockable table bellows cover and attaches the bellows to the table side covers.
      - Checking the touch-and-go strip function
        Makes sure the touch-and-go strips display the landmark on the In-Room Display (IRD) correctly.
      - Doing a check scan
        A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
    - Replacing the dockable table left-hand middle touch-and-go assembly or side bumper
      Removes the middle bumper on the left-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
    - Replacing the dockable table left-hand handle-end touch-and-go assembly or side bumper
      Removes the handle-end bumper on the left-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
    - Replacing the dockable table right-hand bore-end touch-and-go assembly or side bumper
      Removes the bore-end bumper on the right-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
    - Replacing the dockable table right-hand middle touch-and-go assembly or side bumper
      Removes the middle bumper on the right-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
    - Replacing the dockable table right-hand handle-end touch-and-go assembly or side bumper
      Removes the handle-end bumper on the right-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
  - Replacing table undock mechanism components
    Removes the undock link and lever from the table base and installs replacement components.
- MDP
- Pen Panel

SIGNA™ Hero 3.0T Service Methods
5852800-8EN Revision 1.0
Object ID: 00000018WIA30E82C40GYZ
Topic ID: id_2018530 Version: 2.1
Date: Apr 23, 2020 8:51:41 PM

Installing the tabletop front bumper

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	-	5 minutes	-


Tools and test equipment
Item	Quantity	Part number	Manufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set	1	5113258	-

Procedure

Install the tabletop front bumper onto the table.

Figure 1. Tabletop front bumper
1 M4 x 25 Socket Head Screw
2 M4 x 12 Socket Head Screw
3 Front bumper
Install the two M4 x 25 Socket Head Screws and six M4 x 12 Socket Head Screws securing the front bumper to the tabletop.

Home
Replacements
Patient Table
Replacing a dockable table touch-and-go assembly or side bumper
Provides instructions for replacing a touch-and-go assembly or a side bumper on the dockable table.
Replacing the dockable table left-hand bore-end touch-and-go assembly or side bumper
Removes the bore-end bumper on the left-hand side of the table and provides instructions to replace either the touch-and-go assembly or the bumper and reinstalls the bumper.
Installing the tabletop front bumper
Installs the front bumper onto the dockable tabletop.

1	M4 x 25 Socket Head Screw
2	M4 x 12 Socket Head Screw
3	Front bumper