Home
Replacements
System
Power, Gradient, and RF (PGR) Cabinet
Replacing the ICN Solid State Drive (SSD) - Dell R640
This procedure documents the process for replacing the Image Compute Node (ICN) solid state hard drive (SSD) in the Dell R630 (Generation 6) or R640 (Generation 7) ICN.

Replacements
- Replacement Procedures
- System
  - Coolant draining
  - Hoist Service Kit and Lifting Accessories
  - Power, Gradient, and RF (PGR) Cabinet
    - Cleaning or replacing the body coil blower air flow filter
      Clean and/or replace the body coil blower air flow filter.
    - Auxiliary Board Replacement
    - CAM chassis replacement
    - Dual Drive RF Amplifier Replacement
    - Replacing the Integrated Control Engine (ICE)
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) in the Integrated System Cabinet (ISC).
    - Replacing the Integrated Control Engine (ICE) fan assembly
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) fan assembly in the Integrated System Cabinet (ISC).
    - Replacing the 48V Integrated Control Engine (ICE) DC Power Supply (DCPS)
      Removes the ICE DCPS and installs a replacement ICE DCPS into the Power Gradient RF (PGR) cabinet.
    - ICN Conversion Manual
    - ICN Hard Drive Replacement
    - ICN Hard Drive/SSD Replacement (Dell R620 and R630)
    - ICN On/Off procedure for Sun 4100, 4170, and Dell R620
    - ICN Power Supply Replacement (Dell R620 and R630)
    - ICN Replacement (Dell R620, Dell R630, Sun 4100, 4170, or 4170 M2)
    - Replacing the ICN - Dell R640
      Remove and install the Image Compute Node (ICN).
    - Replacing the ICN Solid State Drive (SSD) - Dell R640
      This procedure documents the process for replacing the Image Compute Node (ICN) solid state hard drive (SSD) in the Dell R630 (Generation 6) or R640 (Generation 7) ICN.
      - Shutting down the ICN
        This procedure documents the proper methods of shutdown for the Dell R-620/630 ICN.
      - Removing the Image Compute Node (ICN) Solid State Drive (SSD)
        Remove the Image Compute Node (ICN) solid state hard drive (SSD).
      - Installing the Image Compute Node (ICN) Solid State Drive (SSD)
        Install the Image Compute Node (ICN) solid state hard drive (SSD).
      - Configuring the ICN - VRE
        Volume Recon Engine (VRE) configuration reinstalls the software onto the Image Compute Node (ICN). This procedure is also needed after ICN replacement.
      - Doing a check scan
        A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
    - Replacing the ICN power supply - Dell R640
      This procedure describes the process of replacing the power supply in ICN.
    - KASC assembly replacement
    - KASC Boards Replacement
    - KASC Fan Replacement
    - Replacing the KASC terminator
      Replace the KASC terminator in the Integrated System Cabinet (ISC).
    - Leak Sensor Strip Replacement
    - Ethernet Switch Replacement
    - PDU/PGR Cabinet Replacement
    - Power Equipment Monitor (PEM) Replacement
    - Power Strip Replacement
    - RF Body or Head Transmit Cable Replacement
    - Terminal Server Replacement
    - eXtreme Gradient Amplifier Replacement
    - XGD Cronus Chassis Replacements
    - XGD Fan Box Assembly Replacement
    - eXtreme Gradient Power Supply Replacement
    - Power Distribution Unit (PDU)
  - Penetration (PEN) Cabinet
  - Heat Exchange Cabinet
  - Global Operator Console (GOC)
- Gradient
- RF
- Coils
- Magnet Enclosure
- Patient Table

Optima MR450w BASE 1.5T System Service Methods
5690012-2EN Revision 3
Object ID: 00000018WIA3084C230GYZ
Topic ID: id_15667313 Version: 5.1
Date: Jul 5, 2021 11:07:35 PM

Replacing the ICN Solid State Drive (SSD) - Dell R640

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	10 minutes	30 minutes	30 minutes


Replacement parts
Item	Quantity	Part number	Manufacturer
Dell 640 (Gen7, Gen7-DL) ICN Solid State Disk Drive	1	5941100-23	-


Safety
Before working in any GE Healthcare MR suite or performing any GE Healthcare service procedure, you must: Have read and understood all hazard conditions and safety requirements in the latest revision of the GE Healthcare MR Service Safety Manual (5452735). Have successfully completed all relevant GE Healthcare Environmental Health and Safety (EHS) courses (or for non-GE employees, equivalent workplace training courses). Comply with all site-specific training and workplace safety requirements. If you have any safety concerns at any time, do not begin work or immediately stop work and move to a safe location. Immediately contact your supervisor or site safety officer for instructions on how to proceed.

Notice

Potential component damage

Electrostatic discharge (ESD) can cause permanent damage to electronic components.

Observe the following ESD precautions:

Work on a static-free mat.
Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to the ground.
Create a common ground for the equipment being worked on by connecting the static-free mat, static strap, and peripheral units to that piece of equipment.