Replacements
- Replacement Procedures
- System
  - Coolant draining
  - Hoist Service Kit and Lifting Accessories
  - Power, Gradient, and RF (PGR) Cabinet
    - Cleaning or replacing the body coil blower air flow filter
      Clean and/or replace the body coil blower air flow filter.
      - Electrical Safety
        You must follow all recommended safety procedures when servicing and working near energy sources.
      - Shutting down the host computer
        Shutting down the host computer shuts down the system safely and turns off the power to the host computer.
      - Removing the body coil blower air flow filter
        Remove the body coil blower air flow filter.
      - Cleaning the body coil blower air flow filter
        Clean the body coil blower air flow filter, if necessary.
      - Installing the body coil blower air flow filter
        Install the body coil blower air flow filter.
      - Starting up the host computer
        How to start the host computer.
      - Doing a check scan
        A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
    - Auxiliary Board Replacement
    - CAM chassis replacement
    - Dual Drive RF Amplifier Replacement
    - Replacing the Integrated Control Engine (ICE)
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) in the Integrated System Cabinet (ISC).
    - Replacing the Integrated Control Engine (ICE) fan assembly
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) fan assembly in the Integrated System Cabinet (ISC).
    - Replacing the 48V Integrated Control Engine (ICE) DC Power Supply (DCPS)
      Removes the ICE DCPS and installs a replacement ICE DCPS into the Power Gradient RF (PGR) cabinet.
    - ICN Conversion Manual
    - ICN Hard Drive Replacement
    - ICN Hard Drive/SSD Replacement (Dell R620 and R630)
    - ICN On/Off procedure for Sun 4100, 4170, and Dell R620
    - ICN Power Supply Replacement (Dell R620 and R630)
    - ICN Replacement (Dell R620, Dell R630, Sun 4100, 4170, or 4170 M2)
    - Replacing the ICN - Dell R640
      Remove and install the Image Compute Node (ICN).
    - Replacing the ICN Solid State Drive (SSD) - Dell R640
      This procedure documents the process for replacing the Image Compute Node (ICN) solid state hard drive (SSD) in the Dell R630 (Generation 6) or R640 (Generation 7) ICN.
    - Replacing the ICN power supply - Dell R640
      This procedure describes the process of replacing the power supply in ICN.
    - KASC assembly replacement
    - KASC Boards Replacement
    - KASC Fan Replacement
    - Replacing the KASC terminator
      Replace the KASC terminator in the Integrated System Cabinet (ISC).
    - Leak Sensor Strip Replacement
    - Ethernet Switch Replacement
    - PDU/PGR Cabinet Replacement
    - Power Equipment Monitor (PEM) Replacement
    - Power Strip Replacement
    - RF Body or Head Transmit Cable Replacement
    - Terminal Server Replacement
    - eXtreme Gradient Amplifier Replacement
    - XGD Cronus Chassis Replacements
    - XGD Fan Box Assembly Replacement
    - eXtreme Gradient Power Supply Replacement
    - Power Distribution Unit (PDU)
  - Penetration (PEN) Cabinet
  - Heat Exchange Cabinet
  - Global Operator Console (GOC)
- Gradient
- RF
- Coils
- Magnet Enclosure
- Patient Table

Optima MR450w BASE 1.5T System Service Methods
5690012-2EN Revision 3
Object ID: 00000018WIA30FD0B40GYZ
Topic ID: id_2016778 Version: 3.4
Date: Jun 22, 2020 5:01:28 AM

Installing the body coil blower air flow filter

Procedure

Install the body coil blower air flow filter.
Secure the body coil blower air flow filter clamp.