Home
Replacements
Patient Table
Replacing the hydraulic cylinder
Removes the hydraulic cylinder from a dockable patient table and installs a replacement hydraulic cylinder.
Installing the left-hand base side cover
Installs the left-hand cover onto the dockable table base.

Replacements
- System
- Gradient
- RF
- Coils
- Magnet Enclosure
- Patient Table
  - Arm Board Hinge and Shoulder Screw Replacement
  - Connector Cover and Handle Hinge Replacements
  - Cotton Rod Replacement
  - Cradle Assembly removal and replacement
    This procedure describes how to remove the cradle from the patient table and how to replace the cradle.
  - Cradle Latch Assembly Replacement
  - Replacing the cradle guide rail
    Replace the cradle guide rail, which is locked in the home position with a latch on the patient table bridge. The latch engages a notch on the cradle guide rail at the rear of the table.
  - Replacing the cradle latch–curved table
    Replace the cradle latch housing for a 32-channel system or a 16-channel system.
  - Cradle Latch Block Replacement
  - Replacing the hydraulic filter
    Removal and installation instructions for replacing the hydraulic filter in the dockable patient table.
  - Hydraulic Fluid Draining and Rotary Pump Replacement Videos
    Visit the MR Service Documentation Website to view video clips showing the process to replace the rotary pump and drain the table hydraulic fluid.
  - Patient Table braking system replacements
    This procedure explains how to replace various components in the Table braking system and how to do various braking system checks at the completion of the replacements.
  - Patient Table Cable Take-up and GEM MUX Box Replacement
  - Patient Table Caster, Wheel and Pad Replacement
  - Patient Table Components
  - Replacing the hydraulic cylinder
    Removes the hydraulic cylinder from a dockable patient table and installs a replacement hydraulic cylinder.
    - Raising the dockable table bellows
      Detaches the dockable table bellows cover from the table base covers and raises the bellows.
    - Removing the right-hand base side cover
      Removes the right-hand cover from the dockable table base.
    - Removing the left-hand base side cover
      Removes the left-hand cover from the dockable table base.
    - Removing the oil catch pan
      Removes the oil catch pan from the dockable patient table.
    - Removing the hydraulic cylinder
      Removes the hydraulic cylinder from a dockable patient table.
    - Installing the hydraulic cylinder
      Installs the hydraulic cylinder in a dockable patient table.
    - Bleeding the patient table hydraulics
      Bleeds the hydraulic lines for the dockable patient table.
    - Installing the oil catch pan
      Installs the oil catch pan onto the dockable patient table.
    - Installing the left-hand base side cover
      Installs the left-hand cover onto the dockable table base.
    - Installing the right-hand base side cover
      Installs the right-hand cover onto the dockable table base.
    - Lowering the raised dockable table bellows
      Lowers a previously raised dockable table bellows cover and attaches the bellows to the table base covers.
    - Calibrating and adjusting the hydraulic cylinder
      Checks the patient table for necessary adjustment following hydraulic cylinder replacement.
  - Replacing the hydraulic rotary pump
    Replaces the hydraulic rotary pump of the dockable patient table.
  - Replacing the table rotary pump couplers
    Replaces the table female or dock male rotary pump coupler.
  - Patient Table Up Limit Replacements
  - Patient table upper bellows and lower base side cover removal
  - Replacing the secondary latch actuating cable
  - Table/dock connector and Touch-n-Go (TnG) cable replacement
  - Replacing table electrical docking mechanism components
    Removes table components related to electrical docking and installs replacement components.
  - Replacing table undock mechanism components
    Removes the undock link and lever from the table base and installs replacement components.
  - Touch-n-Go (TnG) strip and side bumper replacement
- Spectroscopy

Discovery MR750 3.0T System Service Methods
5690009-2EN Revision 4
Object ID: 00000018WIA30522C40GYZ
Topic ID: id_2018262 Version: 2.6
Date: Jul 7, 2021 3:51:54 PM

Installing the left-hand base side cover

Prerequisites


Personnel requirements
Required persons	Preliminary requirements	Procedure	Finalization
1	-	5 minutes	-


Tools and test equipment
Item	Quantity	Part number	Manufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set	1	5113258	-


Required conditions
The rear base cover is installed.

Procedure

Install the left-hand base side cover to the table, brake pedal end first.

Figure 1. Left-hand base side cover
Install the two M5 x 12 Button Head Screws securing the base side cover to the table base.

Figure 2. Base side cover top screws
Install the four M10 x 20 Button Head Screws securing the base side cover to the table base.

Figure 3. Base side cover bottom screws
Tighten the 10-32 x ½ Phillips Head Screw securing the front of the base side cover.

Note: Do not over-tighten the screw. The screw only needs to be snug to the cover.

Figure 4. Base side cover front screw