• Discovery MR750 3.0T System Service Methods
  • 5690009-2EN Revision 4
  • Object ID: 00000018WIA3063B030GYZ
  • Topic ID: id_12374205 Version: 2.2
  • Date: Oct 13, 2021 1:18:24 PM

Installing and troubleshooting BrainWave On Console

This document describes the installation of GEHC MR catalog number M7006AK–BrainWaveHW On Console option.

Personnel requirements
Required personsPreliminary requirementsProcedureFinalization
1-1 hour-
Tools and test equipment
ItemQuantityPart numberManufacturer
Nonmagnetic Titanium Service Tool Kit, Small Set15113258-
#2 Flat Head Screwdriver1--
Phillips #2 Screwdriver1--

The parts in the BrainWave On Console kit are listed in the table below. This hardware requires brnwavpxe option to be installed. Refer to Installing software options with eLicense generated keys for more information.

Replacement parts
ItemQuantityPart numberManufacturer
Lumina Response System. Includes:
  • Two pads with two buttons each
  • OTEC unit and 5m fiber cables
  • 3G controller unit
  • One 65 ft shielded cable for inside scan room
  • One 65 ft cable for outside scan room
  • Mini USB cable
  • Power supply
15728367-
Interface Panel Cable Screwlock Connector246-265067P1-
Y-Trigger Cable12293552 -
Penetration Sub-Panel Assembly12394034-10-
Audio Y Cable15729219-
BNC to J16 Exciter Cable15729222-
Display Port to VGA Video Adapter Converter* 15748906-
SubD-DB9 Male/Female Molded Cable, 50 ft15778183-
Dongle Mini Display Male to Display Female Display 1.2a**15795077-

* For use only if connecting video equipment.

** For use only if connecting video equipment on a T5820 PC.

Safety

Before working in any GE Healthcare MR suite or performing any GE Healthcare service procedure, you must:

  • Have read and understood all hazard conditions and safety requirements in the latest revision of the GE Healthcare MR Service Safety Manual (5452735).
  • Have successfully completed all relevant GE Healthcare Environmental Health and Safety (EHS) courses (or for non-GE employees, equivalent workplace training courses).
  • Comply with all site-specific training and workplace safety requirements.

If you have any safety concerns at any time, do not begin work or immediately stop work and move to a safe location. Immediately contact your supervisor or site safety officer for instructions on how to proceed.

Topic ID: id_SL2723667-1322650

Installation overview

The GE BrainWave On Console option consists of third-party software and hardware that can be used to present fMRI patient stimuli synchronized with MR scanning. This document describes the installation for the BrainWave On Console option. The hardware consists of the response system, including response pads and connecting cables. Cable runs must be made from the magnet through the penetration panel to the control room.

For upgrades from BrainWave Lite, the paradigm that previously used the StimPC must be recreated in the Paradigm Manager on the MR console. Make sure the customer collects the details of that hardware paradigms before you start the upgrade.

Note: The BrainWave On Console option requires that software version 26.0 or later is installed on a Dell T5810 host PC (or a newer model).
Topic ID: id_SL15182506-1322650

Discarded material return policy

The equipment or material being removed by the upgrade have a potential value for service of the installed base. The disposition of such must be controlled by GE. Disposition of the removed material is per GE Medical Systems Policy and Procedures.

Topic ID: id_SL15190699-1322650

Material policy overview

Topic ID: id_SL15190700-1322650

Returned material

Per GE Healthcare Policy 3.9: all requested material is to be returned, as directed, intact and promptly to Renewable Resources. Do not remove or swap any parts from the material to be returned.

Topic ID: id_SL15190701-1322650

Disposed material

Regulations governing the disposal of this equipment or material vary from location to location and from country to country. In order to insure compliance with all local, state, or national environment, health, and safety regulations, dispose of all items per local GEMS policy and procedures and other applicable published guidance. Contact GEMS Recycling Center for assistance.

Topic ID: id_SL15190702-1322650

Material to be returned

All uninstalled components must be returned to GE Renewable Resources for recycling. Contact the appropriate site for return instructions.

Sites in Americas Sites in Asia Sites in Europe Sites in Brazil/Argentina
americas.harvest‐team@ge.comharvest123.team@ge.com BucHarvest@ge.comLA.MaterialProductivity@ge.com
Topic ID: id_SL15190705-1322650

Return kit

If needed, packaging and/or transportation details can be obtained through the local Installation Specialist.

Reuse appropriate containers that new hardware and modules were shipped to site for return of above material.

Topic ID: id_SL15190706-1322650

De-installation procedures

Refer to instructions in this manual for de-installation procedures of site.

Topic ID: id_SL15190707-1322650

Product locator information

Process product locator information for all serialized components removed from the system according to policy.