Replacements
- System
  - Coolant draining
  - Hoist Service Kit and Lifting Accessories
  - Power, Gradient, and RF (PGR) Cabinet
    - Cleaning or replacing the body coil blower air flow filter
      Clean and/or replace the body coil blower air flow filter.
    - Auxiliary Board Replacement
    - CAM chassis replacement
    - Dual Drive RF Amplifier Replacement
    - Replacing the Integrated Control Engine (ICE)
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) in the Integrated System Cabinet (ISC).
    - Replacing the Integrated Control Engine (ICE) fan assembly
      Removal and installation instructions for replacing the Integrated Control Engine (ICE) fan assembly in the Integrated System Cabinet (ISC).
    - Replacing the 48V Integrated Control Engine (ICE) DC Power Supply (DCPS)
      Removes the ICE DCPS and installs a replacement ICE DCPS into the Power Gradient RF (PGR) cabinet.
    - ICN Conversion Manual
    - ICN Hard Drive Replacement
    - ICN Hard Drive/SSD Replacement (Dell R620, R630, and R640)
    - ICN On/Off procedure for Sun 4100, 4170, and Dell R620
    - ICN Power Supply Replacement (Dell R620, R630, and R640)
    - ICN Replacement (Dell R620, Dell R630, Sun 4100, 4170, or 4170 M2)
    - Replacing the ICN
      Remove and install the Image Compute Node (ICN).
      - Shutting down the host computer
        Shutting down the host computer shuts down the system safely and turns off the power to the host computer.
      - Applying LOTO - PGR PDU/Gradient Subsystem
      - Removing the ICN
        Removes the Image Compute Node (ICN) to replace it or to replace the ICN power supply.
      - Installing the ICN
        Installs the Image Compute Node (ICN) into the cabinet.
      - Removing LOTO - PGR PDU/Gradient Subsystem
      - Configuring the ICN - VRE
        Volume Recon Engine (VRE) configuration reinstalls the software onto the Image Compute Node (ICN). This procedure is also needed after ICN replacement.
      - Doing a check scan
        A check scan is done at the conclusion of many procedures. This functional check assures the unit is in good clinical working order.
    - KASC assembly replacement
    - KASC Boards Replacement
    - KASC Fan Replacement
    - Replacing the KASC terminator
      Replace the KASC terminator in the Integrated System Cabinet (ISC).
    - Leak Sensor Strip Replacement
    - Ethernet Switch Replacement
    - PDU/PGR Cabinet Replacement
    - Power Equipment Monitor (PEM) Replacement
    - Power Strip Replacement
    - RF Body or Head Transmit Cable Replacement
    - Terminal Server Replacement
    - eXtreme Gradient Amplifier Replacement
    - XGD Cronus Chassis Replacements
    - XGD Fan Box Assembly Replacement
    - eXtreme Gradient Power Supply Replacement
    - Power Distribution Unit (PDU)
  - Penetration (PEN) Cabinet
  - Heat Exchange Cabinet
  - Global Operator Console (GOC)
- Gradient
- RF
- Coils
- Magnet Enclosure
- Patient Table
- Spectroscopy

Discovery MR750w and SIGNA™ Architect T 3.0T System Service Methods
5690002-2EN Revision 4
Object ID: 00000018WIA30D40B40GYZ
Topic ID: id_2016631 Version: 6.2
Date: Feb 15, 2022 9:59:19 AM

Removing LOTO - PGR PDU/Gradient Subsystem

Procedure

Alert necessary personnel that power is being restored.
Remove the lock and tag.
Switch on the MDP's PDU breaker.
Press the green EMO RESET button on the PDU.

Figure 1. EMO RESET button
Power up the host PC.