| Internal Rev |
12.0
|
|
| Line Frequency |
60, [50, 60] |
|
| Spectroscopy RF Amplifier |
no [yes, no] |
|
| Broadband Transceiver |
no [yes, no]
yes, for spectroscopy option
|
|
| TR Dither |
no [yes, no] |
|
| Governing Body |
fda2 [iec, mhw1, mhw2, fda2]
Selection based on governing
body of country where scanner located
|
|
| Magnet Enclosure Type |
1 |
|
| PAC Type |
2 |
|
| RF Body Coil Vector Z |
12431 |
|
| RF Body Coil Length |
10178 |
|
| RF Body Coil Radius |
3840 |
|
| RF Head Coil Vector Y |
191 |
|
| RF Head Coil Vector Z |
-2800 |
|
| RF Head Coil Length |
6150 |
|
| RF Head Coil Radius |
2095 |
|
| Head Coil Amp Calibration Factor |
0 |
|
| Body Coil Amp Calibration Factor |
0 |
|
| Spectro Amp Calibration Factor |
0 |
|
| Magnet Field Strength |
15000 (1.5T)
10000 (1.0T)
30000 (3.0T)
|
|
| Magnet Serial Number |
[xxxxx] |
|
| Room Shielding |
no [yes, no]
yes, for shielding
no, if
none
|
|
| MagnaShield |
no [yes, no]
yes, for MagnaShield
no,
if none.
|
|
| Shield Cooler Type |
4 [0-6] |
|
| Resistive Shim Power Supply |
0 [0-6] |
|
| External Passive Shim |
no [yes, no]
yes, if external passive shim
no,
if none
|
|
| Passive Shim Drum |
no [yes, no]
yes, if passive shim drum
no,
if none
|
|
| Line Conditioner Type |
2 [0-2] |
|
| Isocenter Vector Along Z-axis |
Initial Values:
8914(1.5T)
12431 (1.0T)
8981
(Cx Magnet)
9985 (LCC300)
12520 (Non-Magnishield Magnet)
15250
(Magnishield Magnet)
Final values determined in procedure
for Electrical Isocenter Calibration
|
|
| Table Movement Limit |
31750 |
|
| Beginning of Travel (mm) |
50 |
|
| End of Travel (mm) |
2568
If cradle travel has not been calibrated then
set to 2550 mm. Refer to procedure for Longitudinal Drive Calibration.
|
|
| Max Grad Shim Value |
280 |
|
| Head Plate Dissipation Limit |
800 |
|
| Body Plate Dissipation Limit |
5000 |
|
| Head Power Supply Limit (watts) |
350 |
|
| Body Power Supply Limit (watts) |
4000 |
|
| Head Plate Voltage |
3000 |
|
| Body Plate Voltage |
6000 |
|
| Head Quiescent Plate Current |
.15 |
|
| Body Quiescent Plate Current |
.7 |
|
| Head Load Line Resistance |
857 |
|
| Body Load Line Resistance |
394 |
|
| Network Loss Value |
1.0715 |
|
| Fixed Hardware Trigger Delay |
10 |
|
| Additional CINE Filter Trigger Delay |
28 |
|
| Minimum Bandwidth for VBI |
2 |
|
| Maximum Bandwidth for VBI for Receiver 1 (Use Guided Install Hardware
tab to change value) |
[250] |
|
| Extended Dynamic Range Threshold |
63 |
|
| Preamp warm Up |
900 |
|
| Ad warm Up |
1200 |
|
| Ovosc Warm Pp |
300 |
|
| Multi Coil T/R Driver Brd Present |
yes [yes, no] |
|
| Header Body Single Line Present |
yes [yes, no] |
|
| Bore Monitor Level 1 Trip Point |
[28-31]
25, for TwinSpeed
28, Wide Open
Enclosure with CRM coil
31, Wide Open Enclosures with BRM coil
29,
for other Enclosures (both CRM & BRM coil)
|
|
| Bore Monitor Level 2 Trip Point |
33 [29-36]
29 for TwinSpeed
32, Wide
Open Enclosure with CRM coil
36, Wide Open Enclosure with BRM
coil
33, for other Enclosures (both CRM & BRM coil)
|
|
| Hysteresis Value For Bore Temp Mon |
[0-3]
3, for TwinSpeed
3, for Wide Open
Enclosures
2, for other Enclosures
|
|
| Offset Value For Bore Temperature |
0 [-9 to 9] |
|
| Rated Output Power (body), Watts |
16000 (1.5T), 7500 (1.0T), 35000(3T) |
|
| Rated Output Power (head), Watts |
2000 (1.5T), 750 (1.0T), 35000(3T) |
|
| Max Average Power (body), Watts |
1000 (1.5T), 750 (1.0T), 1250(3T) |
|
| Max Average Power (head), Watts |
100 (1.5T), 75 (1.0T), 200(3T) |
|
| Max Pulse Energy (body), Joules |
60.0 (1.5T), 30.0 (1.0T), 125.0(3T) |
|
| Max Pulse Energy (head), Joules |
6.0 (1.5T), 3.0 (1.0T), 80.0(3T) |
|
| Max Pulse Width (body), ms |
20 (1.5T), 30 (1.0T), 50(3T) |
|
| Max Pulse Width (head), ms |
20 (1.5T), 30 (1.0T), 50(3T) |
|
| Max Duty Cycle (body) |
0.60 |
|
| Max Duty Cycle (head) |
0.60 |
|
| RF Amplifier Type |
0 [0,1,3,4,10]
0, Erbtec Tube (Not available for
Release 10.x)
3, Teal Solid State (1.0T)
4, Analogic
Solid State (1.5T)
10, 1.5T SRFD2
11, 35KW MKS (3T)
|
|
| Power Monitor Type |
[0,1, 2, 3, 4]
0 for 1.0T SSM
1 for
1.5T SSM
2 reserved for Hino Power Monitor
3 for
UPM in Pulse Mode (UPM 1.5T)
4 for UPM in Averaging Mode (UPM
3.0T)
|
|
| Image Compression Value |
73 [50-100] |
|
| Gradient GAP or GIP Board Present |
yes [yes, no]
yes, for ACGD
|
|
| Gradient Amplifier’s Type |
[8280, 8645, 8651, 8915, 8916 and 8905]
8915 for
ACGD or 8905 for ACGD Lite
(Other amp types not available for
Release 10.x)
8916 for HFD
|
|
| X-axis GRAM |
gram-1 [no-gram, gram-0
gram-1, gram-2]
no-gram,
for Base
gram-1 for all others
|
|
| Y-axis GRAM |
(Same as X-axis GRAM) |
|
| Z-axis GRAM |
(Same as X-axis GRAM) |
|
| X-axis ASM Present (Only for 8645 amp) |
yes [yes, no]
yes or no for ACGD
|
|
| Y-axis ASM Present |
(Same as X-axis ASM) |
|
| Z-axis ASM Present |
(Same as X-axis ASM) |
|
| X-axis GASM Present (Only for 8645 amp) |
yes [yes, no]
yes or no for ACGD
|
|
| Y-axis GASM Present |
(Same as X-axis GASM) |
|
| Z-axis GASM Present |
(Same as X-axis GASM) |
|
| X-axis Series (Only for 8645 amp) |
yes [yes, no]
yes or no for ACGD
|
|
| Y-axis Series |
(Same as X-axis Series) |
|
| Z-axis Series |
(Same as X-axis Series) |
|
| X-axis Number of Power Modules(Only for 8645 amp) |
[1, 2]
1 or 2 for ACGD and HFD
|
|
| Y-axis Number of Power Modules |
(Same as X-axis) |
|
| Z-axis Number of Power Modules |
(Same as X-axis) |
|
| Gradient Digital Tuning |
yes [yes, no] |
|
| Gradient Real Time Monitoring ON |
yes [yes, no] |
|
| Gradient Coil Type |
[1,2,3]
1 for CRM (not applicable)
2
for BRM
3 for TRM
|
|
| maxB1 strength (uTesla) |
25.0 |
|
| Maximum integrated (B1) ^2 per pulse (uT^2sec) |
8.0 |
|
| MaxRMS B1 strength for headcoils (uTesla) |
7.2 |
|
| Faster Prescan on/off |
1 [0, 1] 0=Off; 1=On
|
|
| Software Gradient Update Time |
4 |
|
| Hardware Gradient Update Time |
4 |
|
| Software RF Update Time |
2 |
|
| Hardware RF Update Time |
2 |
|
| Software SSP Update Time |
1 |
|
| Hardware SSP Update Time |
1 |
|
| Scanner Mode |
0 |
|
| isCoillD |
0 |
|
| Table is fixed or not? |
N |
|
| Position A, Angle X |
0 |
|
| Position A, Angle Y |
0 |
|
| Position A, Angle Z |
0 |
|
| Position B, Angle X |
0 |
|
| Position B, Angle Y |
0 |
|
| Position B, Angle Z |
0 |
|
| Position C, Angle X |
0 |
|
| Position C, Angle Y |
0 |
|
| Position C, Angle Z |
0 |
|
| Offset X |
0 |
|
| Offset Y |
0 |
|
| Offset Z |
0 |
|
| Does site have moving metal compensation |
0 |
|
| TG of moving metal coil |
0 |
|
| R1 of moving metal coil |
0 |
|
| DFM delta frequency |
0 |
|
| Idle time after scan until coldhead operation is restored |
30 |
|
| X shim for moving metal small sample |
0 |
|
| Y shim for moving metal small sample |
0 |
|
| Z shim for moving metal small sample |
0 |
|
| Z2 shim for moving metal small sample |
0 |
|
| Flag to indicate if system has Z2 coil |
0 |
|
| isZ2autoshim |
0 [0,1] |
|
| FFT coefficient for spiral (128 matrix) |
0.0006555 |
|
| FFT coefficient for spiral (256 matrix) |
0.0006555 |
|
| FFT coefficient for spiral (512 matrix) |
0.0006555 |
|
| FFT coefficient for spiral (1024 matrix) |
0.0006555 |
|
| Spiral regridding coefficient |
0.00001035 |
|
| Gradient amplifier group delay |
120 |
|
| RF Delay |
56 |
|
| Stand By Time |
60 |
|
| DBdtDistance |
27.5 |
|
| Digital tuning board type |
Yes |
|
| Scale used for multiplying DFM shim current |
300 |
|
| DBdtLimit |
0 |
|
| Swing Table (yes or no) |
no |
|
| Zoomlim fov |
1 |
|
| Zoomlim ctl |
1 |
|
| USSS Driver |
yes |
|
| Calibration Type |
1 |
|
| derateb1 body factor |
0.75 |
|
| SAR body NV Weight Limit |
110 |
|
| derateb1 NV Factor |
0.75 |
|
| JSTD Multiplier Body |
0.0654 |
|
| JSTD Multiplier NV |
0.0219 |
|
| JSTD Exponent Body |
1.0696 |
|
| JSTD Exponent NV |
1.154 |
|
| WIM and Duplex PC Connected to SCP |
No |
|
| Waveform suplex run on the Host |
Yes |
|
| Cross Point Switch Type |
1 |
|
| Gradient Processor Type |
2 |
|
| Enhanced Recon Enable |
0 |
|
| Spectro RF Amp Type |
1 |
|