Updates added for Rev 27, May 2022 release:

1. Added Finalization Step "Geometry Verification" to Gradient Switch Replacement Procedure tacrea3

Updates added for Rev 26, January 2019 release:

Updates added for Rev 26, January 2019 release:

1. Replaced ow2sca8i (Host Software Install Release 9.1) in "Operator Workspace and Computer" with DOC2191008 (9.1 Host Load from Cold Procedure using the repackaged software disk)
2. Renamed Direction 5407677 "MR Magnet Safety Requirements" to "Pre-11.x Service Methods Addendum"
3. Planned Maintenance (Direction 2203808) changed to Rev 9

   • Updated Section 1-7 (Pneumatic Patient Alert System)

   • Added "Software Revision Check for Safety" to Section 11

Updates added for Rev 25, November 30, 2010 release:

1. Per iTrak 13196880 and Trackwise 2574982, made the following changes to the PM Manual - Direction 2203808 to Rev 8:

• Updated Introduction (Pages 1-4) and included the PM Schedules, thereby obsolescing Directions 2215702 and 2215703

• Added Section 7-12 to Chapter 2, PM Procedures

• Added the Direction number and Rev to all footers in the A-F PM Schedules

2. Per CAPA 1859293, added the new MR Safety Addendum, Direction 5407677, and updated the following with Warnings/text:

• ME1REA1.DOC, SRI AND DOCK HARDWARE to Rev 2

• ME1SCA3.DOC, ENCLOSURE COVERS AND DOCK ADJUSTMENTS to Rev 4

• ME2SCA2.DOC, ENCLOSURE COVERS AND DOCK ADJUSTMENTS FOR OPEN ENCLOSURE to Rev 4

• MI0REA2.DOC, BLOWER BOX MOTOR REPLACEMENT AND ADJUSTMENT to Rev 3

• PT1SCA2.DOC, LIGHTWEIGHT PATIENT TRANSPORT ADJUSTMENTS to Rev 1

• PT1SCA4.DOC, DUAL TABLE ALIGNMENT PROCEDURE to Rev 1

• RP1REA1.DOC, REAR PEDESTAL HARDWARE REPLACEMENT FOR NON-CX MAGNET to Rev 3

• RP1REA1A.DOC, REAR PEDESTAL HARDWARE REPLACEMENT FOR CX MAGNET to Rev 3

• RP2REA4.DOC, REAR PEDESTAL REPLACEMENT OPEN ENCLOSURE to Rev 2

• PM_SEC1.DOC, Planned Maintenance - Magnet Room

• PM_SEC3.DOC, Planned Maintenance - Patient Handling

• Direction 2304881, Signa 1.5T TwinSpeed System Upgrade Installation

• Direction 2223753, Signa MR/i and CV/i Upgrades

• Direction 2248333, Magnet and System Upgrade to Signa WideOpen (HiSpeed and EchoSpeed)

• Direction 2223752, Signa MR/i and CV/i System Installation

• Direction 2294004, Signa TwinSpeed System Installation

3. Per SPRs MRIhc47186 and MRIhc44718 eliminated the PIN Diode Replacement procedure in:

• Direction 2135785, Signa Phased Array Shoulder Coil to Rev 2

• Direction 2131751, Signa 1.5T GP Flex Coil to Rev 3

4. Per SPR MRIhc52545, updated Direction 2138247, Signa Illustrated Parts List

Updates added for Rev 24, November 15, 2009 release:

1. Per SPR SVCge48089: Added a Note to Table 1 and Section 3-2 Configuration for 2292662 Type Medcam Baseboard for 2292662-11.
2. Per PQR 13266277: Added Section 4.1 Using Gradient Insertion Tool 2164744-6 or Greater.
3. Per PQR 13266277:  Added Section 4.1 Using Gradient Insertion Tool 2164744-6 or Greater.

Updates added for Rev 23, June 30, 2009 release:

1. Per PQR 13176796: Created new document named System Errors as a result of FUS Option.
2. Per PQR 13207656: Updated Direction 2375136-7, 1.5T Mark 9000 Phased Array Shoulder Coil Service Manual.
3. Per PQR 13212305: Created a new procedure: HP4000 Networked Printer Setup.
4. Per PQR 13220158: Updated Signa Teledyne Surface Coil Test.
5. Per PQR 13198522: Updated Direction 2203808, Section 3: Patient Handling.

Updates added for Rev 22, January 2009 release:

1. Per PQR 13112024: Created new document for NEC1990SX and updated Basic or Generic LCD Monitor Calibration & Gamma Setup.
2. Per PQR 13127456: Updated Direction 2205522 to Revision 3 with correct cardiac phased array coil.
3. Per PQR 13171671: Updated Gradient Coil Replacement for BRM, BRM-D & CRM for use with 4 bolts to Revision 8.
4. Per PQR 13165487: Updated MEDCAM AP Board Replacement/Upgrade to Revision 2.

Updates added for Rev 21, June 2008 release:

1. Per PQR 13118083: Added Section D-5, Film Artifacts, due to HW issues.
2. Per PQR 1106480: Changed Section 1-2 to Safety and moved Warning statements from former Sections 1-2 and 1-3.

Updates added for Rev 20, March 2008 release:

1. Per PSR 13094200 & 13113617: Added EHS Lifting Policy Warning statements to ACGD SGA Power Supply Replacement.
2. Per PSR 13142068: Added Electric Shock Danger statement to Gradient Amp Power Supply Replacement.
3. Per PSR 13118251: Added Geometry Verification Important statement to:

• ACGD Cabinet Troubleshooting Flowchart
• GRAM Troubleshooting Harness
• 8645/GRAM Troubleshooting
• SGD HI Slew Problem Isolation
• SGD Base Cabinet Troubleshooting Flowchart

4. Per PSR 13135738: Added Customer Password Management Process.
5. Per PQR 13113617: Updated Chiller Vendor Manual to Revision 9.

Updates added since Rev 19 release:

1. Oct. 16, 2007: Updated Direction 2223752, Signa MR/i & CV/i: System Installation Manual to a Revision 14. 
2. Oct. 17, 2007: Per PSR 13105722, all procedures utilizing the Universal Hoist Kit were updated with a Warning statement.
3. Oct. 17, 2007: Per PSR 13108468, procedures relating to the Cradle Release were updated.
4. Nov. 30, 2007: Revision 4 update for Signa Lx ConnectPro (HIS/RIS) PQR(s):

• 13104792
• 13084868
• 13104789
• 13104791