Topic ID: id_17479525
Version: 3.0
Date: May 23, 2022 11:24:23 PM

DoD16 Error Code List

1 DHCB Error Messages

Table 1. DHCB Error Messages
Error Code	Message	Explanation
260007815	DHCB General Error
260007816	DHCB I2C Error
260007817	DHCB EEPROM Verify Readback error
260007818	DHCB On-Detector EEPROM error
260007819	DHCB On-Board EEPROM error
260007820	DHCB Spare error
260007821	DHCB Spare2 error
260007822	DHCB Heater Fault error
260007823	DHCB receive serial timeout error
260007824	DHCB Sensor and/or Control Abort error
260007825	DHCB Manufacturing Info & Config Table invalid error
260007826	DHCB Temperature Monitor & Control Configuration Table invalid error
260007827	DHCB A/D error
260007828	DHCB Clock-Lost Logic error
260007829	DHCB is in Service Mode
260007830	DHCB was reset
260007831	DHCB State Bipmap Ermes Number not found on lookup table
260007840	DCB-to-DHCB Communications Failed - Exhausted Comm retries	The DCB sent the command to the DHCB. The failures are as follows: 1) DHCB UART sem4: xxx; 2) DHCB Packet ready sem4: xxx; 3) DHCB Nack response: xxx; 4) DHCB Packet size mis-match: xxx
260007841	DHCB is present and connected
260007842	DHCB is not connected
260007843	DHCB Communications established
260007844	DHCB Communications can't be established
260007845	DHCB is in Normal State
260007846	DHCB is in Error Reslove State - DHCB Error is as follows: %b
260007847	DHCB is in shutdown state after attempting to clear faults %d times
260007848	DHCB has issued an abort condition - DHCB Error is as follows: %b
260007849	DHCB has issued a warning condition - DHCB Error is as follows: %b
260007850	DHCB has CLEARED the following error: %b
260007851	The DHCB has detected an illegal Thermister Configuration.	The detected illegal thermister configuration is: left zone: %d (1 = thermister found, 0 = none found): center zone: %d; right zone: %d
260007852	Detector Manager has failed to perform the Detector plug-n-play test	Perform a DAS/COLL reset to attempt test again

2 Detector Error Messages

Table 2. Detector Error Messages
Error Code	Message	Explanation	Potential Root Cause
260132840	Interface Board FPGA Image in DCB is invalid	DCB could not found IFB fpga image	DCB flash problem
260132841	Interface Board(s) FPGA Configuration Failed	DCB could not configure IFB FPGA	DCB-IFB connection
260132842	Detector Module not Connected ModuleList: %s	none of the asic can finish read/write successfully	module-IFB connection, broken module
260132843	VYPER ASIC Read write failed Module: %d; Connecting Status: xxx; Each Asic Ping Status (from NO.1 to NO.6, 0 is good/1 is failed): xxx	one or more asic read/write failed	module-IFB connection, broken module
260132844	Module Hart Of Detector Module is invalid Module: %d	detector module hart info checksum error	module-IFB connection, broken module
260132845	Trim Table Of Detector Module is invalid Module: %d	trim table info checksum error	module-IFB connection, broken module
260132846	IFB Hart is invalid DIFB: %d	IFB hart info checksum error	broken IFB
260132847	IFB Board(s) Detected A Failure Performing 2v5_dvdd_a Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132848	IFB Board(s) Detected A Failure Performing 2v5_avdd_a Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132849	IFB Board(s) Detected A Failure Performing 3v3 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132850	IFB Board(s) Detected A Failure Performing 2v5_avdd_rtn_mod17 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132851	IFB Board(s) Detected A Failure Performing 2v5_io Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132852	IFB Board(s) Detected A Failure Performing 2v5_avdd_c Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132853	IFB Board(s) Detected A Failure Performing 2v5_dvdd_b Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132854	IFB Board(s) Detected A Failure Performing 2v5_avdd_d Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132855	IFB Board(s) Detected A Failure Performing 2v5_lvds Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132856	IFB Board(s) Detected A Failure Performing 2v5_avdd_b Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132857	IFB Board(s) Detected A Failure Performing 2v5_dvdd_rtn_mod_4 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132858	IFB Board(s) Detected A Failure Performing 3v3_ref Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132859	IFB Board(s) Detected A Failure Performing 1v2 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132860	IFB Board(s) Detected A Failure Performing avss_rtn_mod_17 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132861	IFB Board(s) Detected A Failure Performing D_gnd_000 Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132862	IFB Board(s) Detected A Failure Performing avss Voltage Read Operation, DIFB: %d; Exp: %d mV; Act: %d mV	IFB Power error	broken IFB
260132863	Detector Module Temperature is out of limit (60 Celsius Degrees), Detector Power will be shut down, Module: %d; Sensor1 (0.01C/LSB): %d; Sensor2 (0.01C/LSB): %d; Average Temp (0.01C/LSB): %d	detector module temperature higher than 60 degree C
260132864	VYPER ASIC Alpha32 Calibration Error, IFB: %d; Fpga: %d; Module: %d; Asic Status (0:Normal 1:Alarm): Asic0: %d, Asic1: %d, Asic2: %d, Asic3: %d, Asic4: %d, Asic5:%d	Vyper asic alpha calibration error (stage 2-3)
260132865	VYPER ASIC Alpha21 Calibration Error, IFB: %d; Fpga: %d; Module: %d; Asic Status (0:Normal 1:Alarm): Asic0: %d, Asic1: %d, Asic2: %d, Asic3: %d, Asic4: %d, Asic5:%d	Vyper asic alpha calibration error (stage 1-2)
260132866	Broken temperature sensor on detector module detected the sensor number did not change in 100 query, Module ID: %d; Sensor status (1:ok 0:broken): Sensor 1: %d, Sensor 2: %d	module temperature do not change	module-IFB connection, broken sensor
260132867	IFB rx fifo full in below link, IFB link: %s	link status of the data
260132868	Error happened in Comm link between IFB and DCB, IFB num: %d; FPGA num: %d	DCB-IFB comm timeout or CRC error

3 DCB Error Messages

Table 3. DCB Error Messages
Error Code	Message
260132300	DAS CAN Communication Object Initialization Error, Object Id: %d; Error Code: %d
260132301	Unable to open remote CAN node for communication. Attempted To Open CAN Node Id: %d; Received Error Code: %d
260132302	Unable to open communication object, Object Id: %d; Error Code: %d
260132303	Unable to close communication object, Object Id: %d; Error Code: %d
260132304	Scan ABORT -- DAS Has Detected An Error. Communication object (OID) %d; detected receive error %d; MessageCode: xxx.
260132309	Scan ABORT -- DAS Has Detected An Error. Unable to send message %d to CAN node: %d object: %d. Communication error %d detected.
260132310	Not all data acquisition system tasks have started. Task initialization flags are: xxx
260132311	Unable To Create Data Acqusitition System Task. Operating System Error Code: %d
260132316	Scan ABORT -- DAS Has Detected An Error. Operating system ERROR %d detected.
260132317	Scan ABORT -- DAS Has Detected An Error. Memory Allocation failure. Unable to allocate %d bytes of memory.
260132320	Scan ABORT -- DAS Has Detected An Error. DAS was receiving Acquisition Triggers when a First View Azimuth message was received. (Scan State: %b) Trigger Frequency: %d Hz. (Triggers: %d Views - Odd: %d, Even: %d).
260132321	Scan ABORT -- DAS Has Detected An Error. DAS was expecting Acquisition Triggers when a First View Azimuth message was received. (Scan State: %b)
260132322	Scan ABORT -- DAS Has Detected An Error. Unexpected Acquisition Trigger received. (State: %b Command Level: %b ScanState: %b)
260132324	Scan ABORT -- DAS Has Detected An Error. Acquisition hardware (DCB) has detected an Unacceptable Amount of Acquisition Trigger Jitter. (Trigger Frequency: %d hertz). (State: %b Command Level: %b ScanState: %b)
260132329	Scan ABORT -- DAS Has Detected An Error. Data acquisition control board, command table error. Command %d has a NULL function pointer. Command level is: %d.
260132330	Unable To Notify DCB State Machine Of Scan Event. Scan Event:%d; Error code:%d.
260132331	DAS Has Detected An Error In Download Operation. Invalid download code received. Received code: %d
260132332	DAS Has Detected An Error In Download Operation. Download request is too large for DAS buffers. Request was for %d bytes. Maximum buffer size is %d bytes.
260132333	DAS Has Detected An Error In Download Operation. Download operation request codes do not match. Base download request code is: %d. Download request code embedded in operation is: %d.
260132334	DAS Has Detected An Error In Download Operation. Downloaded image corrupted. Base download request code is: %d.
260132345	DAS Has Detected An Error In Download Operation. FLASH memory write error.
260132346	Invalid Trigger Frequency Rx Parameter Received. Requested: %d hertz. Valid range is: %d to %d hertz.
260132347	Invalid DAS Gain Rx Parameter Received. Data Channel Gain: %d. Z Lower Channel Gain: %d. Z Upper Channel Gain: %d.
260132350	Rx Selected An Invalid View Format Type. Data Acquisition Hardware/Firmware Does Not Support the Requested View Format. Check DAS configuration. View Format Requested: %x
260132352	Scan ABORT -- DAS Has Detected An Error. Error detected accessing data acqusition system hardware.
260132354	Scan ABORT -- DAS Has Detected An Error. Scan Setup Errors Prevent The Data Acquisition System From Being Able To Scan. (See Previous Log Entries.)
260132355	DAS Selftest Command Table Error Prevents Execution Of Selftest. Selftest command %d has a NULL function pointer.
260132364	Scan ABORT -- DAS Has Detected An Error. Errors detected while Reconfiguring the Acquisition system for Scan Data Views.
260132368	Null Statemachine Control Structure Pointer Received.
260132384	Scan ABORT -- DAS Has Detected An Error. The DAS has received an invalid command. Command %d is not recognized by the DAS. (DAS CommandState: %b, CommandLevel: %b, ScanState: %b)
260132385	Scan ABORT -- DAS Has Detected An Error. The DAS has received an out-of-sequence command. Command %d cannot be accepted when the DAS is in the State: %b, CommandLevel: %b, ScanState: %b.
260132390	DCB failure detected while writing to %b. (Address: xxx) Expected: xxx, Actual: xxx
260132405	DCB detected Coverter Board Fault Line Asserted. No Detected Configured Converter Board(s) Asserted it.
260132410	DAS Rx Message Is Corrupt. Expected and Actual Rx Message CRC's Do Not Match.
260132416	Self test TIMEOUT occurred on Internal Trigger Scan.
260132419	Detector Temperature Has Returned To Normal.
260132421	DCB Current State Level is INVALID. Current State Level: %d.
260132428	The DAS did NOT receive any Triggers. The scan will be Aborted.
260132444	Scan ABORT -- DAS Has Detected An Error. DAS was expecting EXPCMD Interrupt when a Start Internal Triggers Acquistion message was received. (Scan State: %b)
260132445	Scan ABORT -- DAS Has Detected An Error. DAS was NOT expecting Stop Internal Triggers message during a Internal Triggers Acquistion. (Scan State: %b)
260132455	Beam Tracking Calculated A Focal Spot Size. That Has Exceeded The WARNING Tolerance. Tolerance: %6d umf, Caclulated Size: %6d umf, Nominal Size: %6d umf
260132457	Beam Tracking Control Loop Error Exceeded The WARNING Tolerance. Tolerance: %6d umd, Control Error: %6d umd, Beam Side: %b
260132458	Beam Tracking Control Loop Error Exceeded The ABORT Tolerance. Tolerance: %6d umd, Control Error: %6d umd, Beam Side: %b
260132461	Beam Tracking Detected Signal Corruption. mA Level: %ld, Z Channels: %ld, Offset Vector: %ld
260132470	Unable to Notify Detector Manager Command to the Detector Manager Task. Error code %d received.
260132486	Scan ABORT -- DAS Has Detected An Error. Acquisition hardware (DCB) has detected an INVALID Number of Views versus Triggers. (Trigger Frequency: %d Hz). (Triggers: %d, Views - Odd: %d, Even: %d). (State: %b, Command Level: %b, ScanState: %b)
260132487	Scan ABORT -- DAS Has Detected An Error. The DCB has detected IFB First View Timeout error(s). IFB First View: Timeout: %u nsec. (IFB First View Timeout Interrupt)
260132488	Scan ABORT -- DAS Has Detected An Error. The DCB has detected IFB Subsequent View Timeout error(s). IFB View: Timeout: %u nsec. View Number: %u. (IFB Subsequent View Timeout Interrupt)
260132489	Scan ABORT -- DAS Has Detected An Error during Acquisition. (Trigger Frequency: %d hertz). (Triggers: %d). (State: %b Command Level: %b ScanState: %b)
260132490	An illegal summation cell was specified in the DAS Rx provided by the host. Row: %d Cell: %u.
260132491	Thread object of class \"%b\" unexpectedly destructed.
260132494	Unable to create the DCB Message Queue object creation status: %d, queue size: %d entries
260132495	Unable to create the DCB Message buffer Pool object creation status: %d, creating %d buffers of %d bytes each
260132496	DAS Has Detected An Error In Download Operation. Expected the download message state to be: %b. Found the message state instead to be: %b.
260132502	Scan ABORT -- DAS Has Detected An Error. The DCB has detected IFB DPA Lost Lock error(s). View Number: %d.
260132503	Scan ABORT -- DAS Has Detected An Error. The DCB has detected IFB Checksum error(s). View Number: %d.
260132504	Scan ABORT -- DAS Has Detected An Error. The DCB Has Detected An Interface Board Has failed To Generator The Correct Number of Views. Interface Board:%d, DCB Trigger Count: %d, IFB Trigger Count: %d, IFB Data Count: %d, IFB View Ouput: %d
260132509	Scan ABORT -- DAS Has Detected An Error. The DCB has detected Ifb Rx FIFO Fill error(s). Skew 0: xxx, Skew 1: xxx, Skew 2: xxx, Skew 3: xxx
260132510	Scan ABORT -- DAS Has Detected An Error. The DCB detected IFB view data checksum error.
260132516	Communication To The Command Fan Control Board Has Not Been Established. Scanning Is Disabled Until The Thermal Status of the DAS is Known.
260132517	Communication To The Detector Heater Control Board Has Not Been Established. Scanning Is Disabled Until The Thermal Status of the DAS is Known.
260132521	Hold Wait For Setup Done State.
260132522	Pending Rx Wait For Setup Done State.
260132523	Attempt to dereference an invalid iterator.
260132524	The DAS Has Detected Missing Triggers During This Acquisition. This Typically Occurs Due to Slip-Ring Brush Disconnect. Call Service For Maintenance. Trigger Count: %d
260132525	Platform Trigger Count
260132526	Scan ABORT -- DAS Has Detected An Error. Specified scan will overflow the IFB's internal buffers. # Triggers (views): %u, Trigger frequency: %u Hz, IFB Buffer size: %u MBytes
260132527	DAS has Detected Issue with mA/kV Packets. Triggers Received: %u, Scorp Packets received: %u, Scorp Checksum errors: %u
260132528	DAS has Detected Optical high speed link dropped packets. OpticalKError: %u, OpticalRdError: %u, OpticalRsdCwDecFail: %u, OpticalRsdCwError: %u, OpticalLocked: %u
260132529	Scan ABORT -- DAS Has Detected An Error. 0 - Check Passed, 1 - Check Failed, 255 - The check was not done, IFBs Ready: %u, Acq Setup Failed: %u, Odd No of PreTrigg: %u
260132530	Scan ABORT -- DAS Has Detected An Error. Did not get the minimum number if offsets Min no of offset triggers required: %u, No of offset triggers received: %u
260132531	DAS has not detected any IFB. 0 - DAS will Abort all scans, 1 - DAS will Scan in simulated Mode, DAS Status: %u
260132532	Setup Scan Sequence Error. Error in step: %b.
260132556	Incorrect Power Module ID was requested. Requested ID: %d, Available ID: 1 or 2
260132557	Over Temperature Condition of Power Module was Detected. PM1-1: %d deg, PM1-2: %d deg, PM1-3: %d deg, PM1-4: %d deg, PM1-5: %d deg, PM2-1: %d deg, PM2-2: %d deg, PM2-3: %d deg, PM2-4: %d deg, PM2-5: %d deg
260132558	At Least One of Temperature Sensors of Power Module is Broken or Disconnected. The Status is below. 1 means alive. PM1-1: %d, PM1-2: %d, PM1-3: %d, PM1-4: %d, PM1-5: %d, PM2-1: %d, PM2-2: %d, PM2-3: %d, PM2-4: %d, PM2-5: %d
260132559	Incorrect Temperature Sensor ID of Power Module was requested. Requested Temp Sensor ID: %d, Requested Power Module ID: %d, Available Temp Sensor ID: 1 - 5

4 KFC Error Messages

Table 4. KFC Error Messages
Error Code	Message	Explanation
260132980	DCB-to-KFC Communications Failed - Exhausted Comm retries. The DCB Sent The Command to the KFC. The Failures are as follows: KFC UART sem4: %d, KFC Packet ready sem4: %d, KFC Nack response: %d, KFC Packet size mis-match: %d
260132981	Read KFC Memory Command.
260132982	Write KFC Memory Command.
260132983	Query KFC Status Command.
260132984	Update Temperature Information to KFC Command.
260132985	KFC Ermes Number not found on lookup table.
260132986	KFC is present and connected.
260132987	KFC is not connected.	KFC intermits communication with DCB
260132988	KFC Communications established.
260132989	KFC Communications can't be established.
260132990	The KFC has detected a thermistor open failure. Thermistor: %d	KFC sensor opens
260132991	The KFC has detected a thermistor short failure. Thermistor: %d	KFC sensor shorts
260132992	The KFC has detected a fan failure. Fan: %d	KFC fan failure
260132993	The KFC has detected an inlet over temperature failure. Inlet: %d	Inlet and Outlet over temperature
260132994	The KFC has detected an outlet over temperature failure.	Inlet and Outlet over temperature
260132995	The KFC has recovered from a thermistor open failure. Thermistor: %d
260132996	The KFC has recovered from a thermistor short failure. Thermistor: %d
260132997	The KFC has recovered from a fan failure. Fan: %d
260132998	The KFC has recovered from an inlet over temperature failure. Inlet: %d
260132999	The KFC has recovered from an outlet over temperature failure.